搜索结果: 1-15 共查到“复合材料 Ti”相关记录55条 . 查询时间(0.035 秒)
中国科学院金属研究所专利:一种用于Ti-Al合金的Al/Al2O3/MCrAlY复合涂层及制备方法
中国科学院金属研究所 专利 Ti-Al合金 Al/Al2O3/MCrAlY 复合涂层
<
2023/12/26
中国科学院金属研究所专利:一种强度可设计可焊接SiCf/Ti基复合材料0/90°层合薄板及其制备方法
中国科学院金属研究所 专利 SiCf/Ti基 复合材料 0/90°层合薄板
<
2023/10/17
中国科学院金属研究所专利:内生韧性相增强Ti基非晶复合材料及其制备方法
中国科学院金属研究所 专利 内生 韧性相 Ti基 非晶 复合材料
<
2023/10/17
中国科学院金属研究所专利:一种TiC/Ti复合泡沫材料及其制备方法
中国科学院金属研究所 专利 TiC Ti 复合泡沫材料
<
2023/9/7
中国科学院金属研究所专利:一种TiAl基合金专用高温Ti基钎料及其制备方法和钎焊工艺
中国科学院金属研究所 专利 TiAl基 合金 Ti基钎料 钎焊工艺
<
2023/8/14
An octane mediated strategy towards Ti-containing HMS-type mesoporous materials incorporated with methyl for high-efficiency oxidative desulfurization
Oxidative desulfurization Ti-HMS Methyl-functionalized Solvent-free Pickering emulsion catalysis
<
2023/6/19
Delicate mediation on structural properties and surface wettability of catalysts is the key strategy towards a high catalytic performance but remains challenging. Herein, organic-inorganic hybrid Ti-c...
采用Al和TiC靶通过磁控共溅射方法制备了Ti∶C≈1的不同Ti和C含量的铝基复合薄膜, 研究了Ti和C含量对薄膜微观结构和力学性能的影响.结果表明: Ti和C的共同加入使复合薄膜形成了同时具有置换固溶和间隙固溶特征的“双超”过饱和固溶体, 复合薄膜的晶粒尺寸在较低的溶质含量下就迅速减小到100 nm以下, 并随溶质含量的增加继续减小. 相应地, 薄膜的硬度也从纯Al的1.3 GPa迅速提高, 在...
Band gap tuning in ferroelectric Bi4Ti3O12 by alloying LaTMO3 (TM = Ti, V, Cr, Mn, Co, Ni, and Al)
Band gap tuning ferroelectric Bi4Ti3O12 alloying LaTMO3
<
2012/2/24
We fabricated ferroelectric Bi4Ti3O12 (BiT) single crystalline thin films site-specifically substituted with LaTMO3 (TM = Al, Ti, V, Cr, Mn, Co, and Ni) on SrTiO3 substrates by pulsed laser epitaxy. W...
原位自生Ti--B--Si--C系复合材料的制备和性能
复合材料 钛基复合材料 原位自生 力学性能
<
2011/12/31
以Ti粉、B4C粉和SiC粉为原料, 用真空热压烧结工艺制备了原位自生颗粒增强的Ti--B--Si--C系钛基复合材料, 研究了复合材料的显微组织和力学性能。结果表明, 使用的初始粉末不同, 原位自生颗粒的组成不同, 复合材料的性能也有明显的差别。
Preparation of porous Al2O3-Ti-C perform by combustion synthesis
preform combustion synthesis composite infiltration
<
2011/3/30
Using combustion synthesis porous ceramic preforms for composite reinforcing were produced. Prepared mixture of alumina Saffil fibres, Ti powder and graphite flakes, after drying were placed in wavegu...
Preparation of porous Al2O3-Ti-C perform by combustion synthesis
preform combustion synthesis composite infiltration
<
2011/3/30
Using combustion synthesis porous ceramic preforms for composite reinforcing were produced. Prepared mixture of alumina Saffil fibres, Ti powder and graphite flakes, after drying were placed in wavegu...